The choice of Open-Top or Flat rack containers isn’t a naming convention, it’s a loading choice. Open-top container is a box with an open (removable) tarpaulin roof and in most units with removable roof bows. It is designed for cargo that can be loaded from either top or end of the unit, but that is too tall for a dry van. A flat container is a container having no side walls and end walls. It’s for goods that are wider than usual, require side entry for lashing or are to be loaded and unloaded as a single piece onto a deck.
This article is a selection method: cargo size, cargo method first, type of container second. Don’t assume that all out-of-gauge bookings are a flat rack. A lot of tall crates are still suitable for an open-top. Even if the height seems to be correct on many wide machines, a flat rack is required.
What Open-Top and Flat-Rack Containers Actually Are
Open top is still a container. The sides stay up. The roof comes off. Cargo is loaded through the open top (or end doors if a forklift or a roller path is available). Once loaded, the roof bows are returned and the tarpaulin is secured for a sea journey. The walls provide a counter to work against during loading.
A flat deck is a flat rack. There are no side walls, but there are end walls, some of which are fixed, and some of which are collapsible. Cargo sits on the platform and is lashed to the deck and end frames. When the carrier and the inland route permit, width may extend over the sides. A steel roof does not limit height as do the rules of permits, stowage and road bridges.
Why buyers mix up open-top and flat rack
There are many common emails in a factory that read, “tall machine, send flat rack.” The first thing that people notice on a photo is the height. Even though the height is out of gauge, the crate may be able to fit in an open-top: The crate will not fit through a door of a dry-van, but will fit inside the side-wall height and width after the roof bows and tarp are removed. Lashing it for width or side lashing or a piece that cannot be secured on a wall, moves the booking to a flat rack.
Every OOG callout is a flat rack, which represents the cost that is being squandered, and is not a virtue for the inland situation. A legal flat rack at berth is not necessarily legal on the truck. An open top available for this sailing is then closed.
Where typical China factory cargo sits
Typically, an open-top is used for tall crates, bagged product that is moved up by crane, and for some pieces of equipment that are not wide, but are tall. Flat rack is used for wide machines, tanks, steel structures and side chain or side frame required parts. Whether it is not a platform at all or it is too large for a container booking even as OOG is another conversation, Breakbulk or project stowage.
Start With Cargo Dimensions and Loading Method
Avoid using a container code as a starting point. Physical brief: actual length, width, height, gross weight, center of gravity, how the plant can be loaded – forklift, overhead crane, side access, or none of these. Include any inland restrictions at both ends of the journey, such as road width, axle restrictions, bridge heights, and even if a permit is available for the route you believe you are going to use.
Photos are only helpful if they include scale. Does not suggest a packing list that reads “machine, 20 tons.” Request a picture of the drawing or a photo with a known wall or pallet using a tape measure. Write if the measurement is for the crate, skid or lifting frame. The container is booked on the packed size and not bare machine.
Test an open-top, before taking a flat rack. Open-top is the first live solution if the piece is tall but not as tall as the side walls and is within normal container width, and the plant can crane through the roof or roll through the end. Oversized and project cargo planning, equipment choice, lifting method, loading sequence, securing plan and route checks should all be in the same brief as they will all come to light later in the process as a rejected booking, a refused truck or a cargo that can’t be legally secured.
Height-only OOG that often fits an open-top
This is cargo that is taller than the door of a dry-van trailer but shorter than the side walls and width of the trailer. Tarp and bows on roof are removed. The crane drops the crate through the top, or the forklift enters the end (if there is enough space to fit). If the goods are not in the bow, the bows go back. The tarp is re-repaired and retied. An open-top is not a closed box, it is an exposed load and you are already in a different risk and permit conversation.
Width or complex OOG that needs a flat rack
This refers to cargo which can’t be accommodated in the normal width container and requires man labor on the side to put on the chains and chocks or can’t be boxed with steel walls. The piece is hoisted as a whole into the deck. If there is an overhang it must be stated. The booking does not include only stowage, lashing and inland permits it is booked at the terminal.

Open-Top Containers: Loading Methods and Practical Limits
In China export work, it is used when the packed height does not fit within a normal door height, but the container’s contents are still considered unitised. The removable tarp and Roofer fenders are working components. Units are NOT like each other. Doors can be tall, or short, bows can be spaced closer or father apart, side walls can be high or low, depending on owner/construction. Check the actual unit before considering a drawing to be a booking spec.
An open-top is parking that is available for the use of any group. FCL and LCL Ocean shipping from China is the planning layer for port-to-port or door movement, only after the cargo has been unitized and the type has been determined.
Top loading vs end loading
Tall loads that cannot be placed in the doors are typically loaded from the top. The crate is dropped by the open roof using a crane or spreader. If there is still height left unobstructed, the forklift, a yard tractor or rollers can be used to unload the cargo from the door end, which is known as end loading. The problem is that one assumes the same internal height and/or the same bow configuration for all open-tops. If there are bows that cannot be moved or are set in awkward positions, a unit that seemed to be a great idea can suddenly become deadly.
Lashing and tarpaulin handling
Lashing points located on side walls and floor. Use them. Lading leaning on the tarp (or lashing that saws across the tarp) will not survive a sea passage. The tarp needs to be put on and fastened. The taller the cargo on a side wall, the more exposed it is to the weather, and the less the tarp will close the box, making the booking not truly an open top load.
Flat-Rack Containers: Platform Loading and Lashing
A flat rack is a platform having end walls. No side walls to conceal a sloppy lift or a shifted crate. A dry van can have width and height that exceeds. Weight still needs to be within payload, axle and stowage limits. Collapsible end walls aid to empty positioning. They are not changing the way in which one lashes a live load.
Loading from the side and end
In most cases, heavy or wide equipment is delivered by crane or heavy lift equipment to the deck from the side. End loading can be done only if width is not too large between end frames. The problem is, assuming that loading a flat with like a dry van, and when the cargo load plan is a few straps “for now” can lead to a cargo walkout. A flat rack will not resolve the handling issues if the plant cannot move it as a whole.
Lashing points and weight distribution
The missing walls are replaced by lashing rings, chains, wedges and dunnage. The weight should be concentrated in the middle of the deck and within the acceptable load range for the truck and the vessel. Apparently harmless overhang in the yard may be a road problem and/or a terminal problem. It is more economical to make a lashing sketch prior to loading than it is to find a shift after the gates close.
Dimensions and Weight—What Importers Must Confirm
A brochure drawing is not the unit that you will receive. Open top container sizes and flat rack container sizes vary depending on the owner, year and build. Check the height of the door, the height of the side walls, the deck length, the width of the inside of the unit, what the unit will carry and whether it is a bow or end wall. The type can be selected with qualitative ranges. The number of exacts shall be entered in the booking file.
Door height, side-wall height, and width limits
The first filter is for dry-van door height. If the packed cargo does not fit through that door, then a standard box is out. Then if the same cargo will fit in the container with the same width, but with its top open, then open-top is the next test. The flat rack is the live container if width is larger than the normal container width or if the piece cannot be placed inside walls. That’s not one of the preferences for the unit that “sounds more project,” it’s one of the sequences.
Payload and inland limits
There’s only one Container payload number. The loaded unit is determined by either axle limits or bridge height or permit at origin/destination and cannot leave the yard. A flat rack which loads at the port but does not move onto the public road is not a completed shipment. Before locking type, be sure to look at both ends.
| Container type | Best for | Loading method | Main dimension limits | Main watch-outs |
|---|---|---|---|---|
| Open-top | Tall cargo that still fits inside side walls and normal width | Top by crane, or end when height allows | Confirm actual door height, side-wall height, width, and roof-bow layout on the unit | Cargo above the walls; tarp not refitted; assuming every open-top is the same height |
| Flat rack | Wide, tall, or side-lashed cargo that cannot be enclosed | Side or end lift onto the deck | Confirm deck size, end-wall type, payload, and legal OOG envelope | No side walls; overhang vs road and port rules; axle and permit limits inland |
A Practical Way to Choose Before You Book
Paste this sequence into the first email:
- Exact packed length, width, height and gross weight, center of gravity and lifting points.
- Does a standard box have a problem on door height only?
- Is the piece open-top side-wall height and width (still in the walls)?
- Do the width, side access or lift method need a platform for flat-rack deck and OOG envelope?
- Inland Permit/Final Delivery—is the unit loaded and can it operate on the real roads at both ends?
Provide photos, packing list and lifting-point information. Please avoid sending “machine, 20 tons, cheapest container.”
Machinery and plant pieces as a worked example
An open-top vs flat rack for machinery case that is taller than the door height of a dry van but does not extend beyond the open top walls and width of the dry van is called a tall crated CNC. A flat rack is a wide press which will not stand between container walls and which requires side chains. If a tank is larger than the legal flat-rack overhang and the open-top envelope, it may be completely removed from the container equipment and require breakbulk planning. That contrast is a filter, NOT a complete machinery SOP. If the live shipment is an industrial equipment, the next planning page to consider is the packing, dimensions, loading, and scope of the shipment for industrial equipment, machinery and heavy equipment.
Mistakes that send cargo to the wrong container
- Assuming all open tops are the same height inside or bow shape.
- Failing to verify road, axle and bridge limits prior to loading a flat rack at origin and destination.
- Assuming that “the yard will take care of itself.”
- Making all OOG bookings breakbulk, where an open-top or flat rack could have done the job.
- Reservations based on a factory photo without width of packed items, lifting points or how the plant can load.
Frequently Asked Questions
What is the main difference between open-top and flat-rack containers?
An open top is a box that has a removable cover. The side walls remain intact. A flat rack is a structure that consists of a platform with end walls and no side walls. The first is meant for taller loads that will still fit within the walls. The second is for goods requiring width or side access or one lift to a deck.
When should I choose an open-top instead of a flat rack?
For a dry van where the packed height matters, but width and side wall height don’t, select an open top, and load either at the top or the end. This is the standard way of loading containers with open tops, typically from China factories and for tall containers.
Can a flat rack handle any width or height?
The size of the deck, load, stowage and inland rules limit how much you can hang up/drop off. There is still a legal envelope on OOG container shipping from China. Be sure to verify the unit and road permits before assuming the term “flat rack” means unlimited.
Do open-top containers require crane loading?
Not always. If the load can’t fit through the doors, it is often loaded at the top with the crane. If height permits, end loading can be done with a forklift or rollers. Check the unit and plant lifting equipment.
What dimensions must I confirm before booking?
Packed length, width, height and gross weight, door height, side-wall height, internal or deck width, payload, bow or end-wall type and inland limits. Use these numbers in the real unit. Avoid a generic drawing.
What details does a forwarder need to recommend a container type?
Packed dimensions and weight, photos or drawing, point of lift, origin/destination addresses and any known road or permit limits. If they are not there, the recommendation is a guess.
Share cargo information for a container assessment if dimensions and weight are known and you need a live assessment or your cargo is in packing state, you are unsure about origin or destination.
